A stripper de arame é usada para SN - 28B Pin Socket Terminal Crinping Tool Crimper de Dupont JST - SM

A stripper de arame é usada para SN - 28B Pin Socket Terminal Crinping Tool Crimper de Dupont JST - SM

€ 5.93

Montante

Tamanho pequeno, clipe pequeno, é muito bom O produto pode travar automaticamente, mais poderoso. O princípio operacional é a estrutura da biela estressada do tipo Ratchet. Pode ser ajustado ajustando a força de prensagem da alça de controle da roda. Operação mais fácil, linhas de pressão mais rápidas. Essa ferramenta de crimpagem pode ser usada para prender os pinos de crimpagem masculino e feminino a 18-28 fios AWG para fabricar cabos personalizados. Especificação : Condiiton : Brand New Color : Blue + Blackmaterial : Ni-CR Steelsize : aprox. (L) x (w) 190 x 150 mm / 7,48 "x 5,51" (aprop. Se estiver no rolo, não corte o pino e deixe -o no rolo até que o fio esteja enrolado. Prepare o fio retirando aproximadamente 1/8 "(3 mm) de isolamento do final. Coloque o fio no pino de crimpagem e alinhe -o para que a parte despojada esteja entre os terminais internos no pino de crimpagem e o fio isolado esteja entre os terminais externos. está no convexo e na metade mais larga do dente. O terminal deve apontar para a cavidade do outro lado do molde, para que a ferramenta dobre a montanha para dentro ao redor do fio ao fechar.


Mais dados

Condiiton:
Brand New
Color:
Blue + Black
Material:
Ni-Cr alloy steel
Size:
Approx. (L) x (W) 190 x 150 mm / 7.48 x 5.51(appr.)
How to use:
1. If it is on the roll, do not cut off the pin, and leave it on the roll until the wire is curled. Prepare the wire by stripping approximately 1/8 (3 mm) of insulation from the end.:
Place the wire in the crimp pin and align it so that the stripped part is between the internal lugs on the crimp pin and the insulated wire is between the external lugs.:
2. If the crimping pin is too short, this method cannot be used. See the bottom of these instructions for alternatives.:
Place the wire and crimp pin on the appropriate tooth of the tool mold, making sure that the insulating end is on the convex and wider half of the tooth.:
The lug should point to the cavity on the other side of the mold so that the tool bends the lug inward around the wire when closing.:
3. Slowly and completely close the tool jaw until it is released.:
Joints on suitably crimped pins shall form a barrel around the conductor of the conductor and another barrel around the conductor insulation to relieve stress.:
4. Or, if the crimp pin is too short for this method (or if it is not on the roll), buckle the crimp pin completely from the fixing strip.:
Insert the crimping tool into the correct groove, and then use the ratchet to hold the crimping pliers in place. Insert the wire from the other end and crimp it.:
Package includes:
1 X SN-28B crimping tool:
Notice:
1. Due to manual measurement, please allow 1-3cm error and make sure you don't mind before ordering.:
2. Please understand that there may be color difference due to different positions of pictures.:
3. Please note that the new model and old model of this product will be sent randomly, and make sure you don't mind before ordering.:

Mais produtos na categoria

Jet 82 grampo paralelo
  • Novo

Jet 82 grampo paralelo

€ 3.36

Muita força : o design exclusivo fornece precisão e potência com pinças exatas de 90 graa até 1 Conforto : A alça de sumogrip ergonômica é integrada a uma aderência suave, para maio